Two thumbnail bits, one clear profile difference
The Whiteside 3302 and 3294 are both large-diameter table edge router bits with a 1/2'' shank, 1'' profile width, 3/4'' cut length, and 2-1/2'' large diameter. The main difference is the profile: the 3302 combines thumbnail and bead, while the 3294 is a straight thumbnail. That single distinction drives which bit suits your table edge.
This comparison sticks to what the catalog confirms. Where a detail is not supplied, such as specific feed rates or RPM limits, I'll note it as a limitation rather than guess.
3302 vs 3294 at a glance
- Profile: 3302: Thumbnail and bead. 3294: Thumbnail only.
- Shank: Both 1/2''.
- Profile width: Both 1''.
- Cut length: Both 3/4''.
- Large diameter: Both 2-1/2''.
- Country of manufacture: 3302: Made in USA. 3294: Not stated in the supplied record.
Catalog evidence for the Whiteside 3302
- Thumbnail and Bead Table Edge Router Bit – Whiteside 3302: Thumbnail and Bead table edge router bit with 1/2'' shank, 1'' profile width, 3/4'' cut length, and 2-1/2'' large diameter. These shared dimensions mean the 3302 fits the same router setup as the 3294; the choice comes down to the bead detail.

Thumbnail and Bead Table Edge Router Bit – Whiteside 3302 - Thumbnail and Bead Table Edge Router Bit – Whiteside 3302: Similar to a standard edge profile bit, but with a much larger profile width. The wider profile is what lets it shape a substantial table edge in one pass, matching the bit's intended use on large workpieces.
- Thumbnail and Bead Table Edge Router Bit – Whiteside 3302: Made in USA. Useful if domestic manufacture is a priority in your tooling purchase.
Catalog evidence for the Whiteside 3294
- Thumbnail Table Edge Router Bit – Whiteside 3294: Thumbnail table edge router bit with 1/2'' shank, 1'' profile width, 3/4'' cut length, and 2-1/2'' large diameter. Identical shank and cutting dimensions to the 3302, so either bit mounts the same way on a 1/2'' router.

Thumbnail Table Edge Router Bit – Whiteside 3294 - Thumbnail Table Edge Router Bit – Whiteside 3294: Ideal for trimming the edges of a large workpiece such as a table. Confirms the 3294 is purpose-built for table edges, not just smaller trim work.
- Thumbnail Table Edge Router Bit – Whiteside 3294: Overall design similar to a standard edge profile bit, but with a much larger profile width. The larger width covers more of the table edge, which is the point of a dedicated table edge bit.
When the bead detail on the 3302 makes sense
Choose the 3302 if you want a decorative bead worked into the thumbnail profile. The bead adds a visual line that can dress up a table edge without requiring a separate bit change. Because the 3302 shares the 3294's 1/2'' shank and 1'' profile width, it fits the same routers and handles the same scale of workpiece.
The tradeoff is that a combined profile leaves less room for error: once the bead is cut, you can't remove it. If you prefer a simpler, more forgiving edge, the plain thumbnail of the 3294 may be the better starting point.
When the plain thumbnail 3294 is the better fit
The 3294 suits tables where the edge should read as a clean, classic thumbnail without extra ornament. Its catalog description specifically calls out trimming large workpieces like a table, so it aligns with that job. With the same 1/2'' shank and 1'' profile width as the 3302, it's a direct alternative rather than a step up or down in size.
If you're matching an existing plain thumbnail edge elsewhere in the room, the 3294 keeps the profile consistent. The 3302's bead would introduce a new detail that may not match.
What the catalog does not settle
Some decisions need information beyond the supplied records. These points are not confirmed either way, so verify them against the bit itself or the manufacturer's documentation before cutting.
- Recommended RPM: No RPM range is supplied for either bit. Large-diameter bits generally call for lower speeds, but confirm the specific recommendation for your router and material.
- Feed rate and pass depth: The catalog gives cut length but not depth-of-cut or feed guidance. Start conservatively and adjust based on the cut.
- Bearing or guide type: Neither record states whether a bearing is included or what type. Check the product page or packaging.
- Material suitability: The records don't list which woods or composites each bit is intended for. The 1/2'' shank and large diameter suggest substantial work, but that is an inference, not a catalog claim.
A practical way to decide
Start with the edge you want. If a bead line belongs in the design, the 3302 is the only one of the two that provides it. If a clean thumbnail is the goal, the 3294 keeps the profile simple. Because both share the 1/2'' shank, 1'' profile width, 3/4'' cut length, and 2-1/2'' large diameter, you're not trading off capacity or router compatibility—only the profile.
If you're still unsure, cut a test piece with scrap stock using the profile you're considering. That will show whether the bead adds to the design or competes with it, and it lets you confirm the setup before committing to the table edge.



