Match the bit to the groove, not the other way around
A straight router bit is defined by three numbers: cutting diameter, length of cut (LOC) and shank size. The diameter sets the groove width, the LOC sets how deep you can go in one pass, and the shank must match your router collet. Get those three aligned with your project and the bit will cut cleanly; force a mismatch and you get chatter, burn marks or a bit that simply will not fit.
This guide uses three Whiteside straight bits from the current catalog to show how the numbers translate into real routing decisions. All three are made in the USA and share a straight-flute design for smooth, controlled cuts, but they differ sharply in diameter, cut length and recommended RPM.
Three straight bits at a glance
- Whiteside 1099: 1-1/2′′ cutting diameter, 1-1/4′′ LOC, 1/2′′ shank, recommended 10,000–12,000 RPM (max 16,000). The widest and deepest of the three.
- Whiteside 1031: 3/4′′ cutting diameter, 1′′ LOC, 1/4′′ shank, recommended 14,000 RPM, 2-5/8′′ overall length. A mid-size bit for joints and grooves.
- Whiteside 1029 (AstraHP Coated): 11/16′′ cutting diameter, 3/4′′ LOC, 1/4′′ shank, recommended 14,000 RPM, 2-1/8′′ overall length. The narrowest and shallowest, with a friction-reducing coating.
Diameter: the width of the cut you need
Diameter is the first decision because it determines the groove or dado width. If you need a 3/4-inch groove, a 3/4-inch bit like the Whiteside 1031 cuts it in one pass. If you need a 11/16-inch groove, the Whiteside 1029 matches it directly. The 1-1/2-inch Whiteside 1099 is for wider grooves, dadoes and general-purpose routing where a broad flat-bottomed cut is required.
A bit that is too wide for your router or your workpiece can be harder to control, especially in a 1/4-inch shank. The 1099 uses a 1/2-inch shank, which provides more stability for its larger cutting diameter. The two smaller bits use 1/4-inch shanks, which suit compact routers and lighter cuts.
Catalog evidence for the 1/2-inch shank bit
- 1-1/2″ Straight Router Bit x 1-1/4″ LOC x 1/2″ Shank – Whiteside 1099: 1-1/2′′ cut diameter, 1-1/4′′ cut length, 1/2′′ shank; recommended 10,000–12,000 RPM (max 16,000); designed for use with a 1/2-inch collet. The 1/2-inch shank and lower RPM range reflect the larger mass of this bit. It is the choice when you need a wide groove and your router accepts a 1/2-inch collet.

1-1/2″ Straight Router Bit x 1-1/4″ LOC x 1/2″ Shank – Whiteside 1099
Cut depth: how deep you can go in one pass
Length of cut (LOC) is the maximum depth the flutes can reach in a single pass, but it is not a target. A bit with a 1-1/4-inch LOC, like the Whiteside 1099, can physically cut that deep, but the recommended RPM range and your router’s power will influence how much material you remove at once. The catalog does not supply pass-depth instructions for these bits, so treat LOC as a ceiling rather than a recommended depth.
For shallower work, the Whiteside 1029 has a 3/4-inch LOC and the Whiteside 1031 has a 1-inch LOC. If your groove is only 1/2 inch deep, a bit with a shorter LOC keeps more of the shank inside the collet and reduces flex. Match LOC to the deepest cut you actually plan to make, not to the maximum the bit allows.
Catalog evidence for the mid-size and coated bits
- 3/4″ Straight Router Bit x 1″ LOC – Whiteside 1031: 3/4′′ cut diameter, 1′′ cut length, 1/4′′ shank, 2-5/8′′ overall length; recommended 14,000 RPM. The 3/4-inch diameter and 1-inch LOC make this a practical all-rounder for joints, dados and grooves. The 1/4-inch shank fits compact routers.

3/4″ Straight Router Bit x 1″ LOC – Whiteside 1031 - 11/16″ Straight Router Bit x 3/4″ LOC – Whiteside 1029 (AstraHP Coated): 11/16′′ cut diameter, 3/4′′ cut length, 1/4′′ shank, 2-1/8′′ overall length; AstraHP coating; recommended 14,000 RPM. The narrow diameter and shorter LOC suit precise, shallow straight cuts. The AstraHP coating is intended to reduce friction and improve wear resistance.
Shank and RPM: the compatibility checks
Before you buy any straight bit, confirm your router’s collet size. A 1/2-inch shank bit like the Whiteside 1099 requires a 1/2-inch collet; it will not fit a 1/4-inch router without an adapter, and the catalog does not list an adapter for it. The 1/4-inch shank bits, the 1031 and 1029, fit routers with a 1/4-inch collet.
The recommended RPM ranges also differ. The 1099 calls for 10,000–12,000 RPM with a maximum of 16,000, while the 1031 and 1029 both recommend 14,000 RPM. Set your router’s speed accordingly; running a large-diameter bit too fast can be unsafe, and running a small bit too slow can leave a rough cut. The catalog does not provide feed-rate guidance, so start with a conservative feed and adjust based on the cut quality.
A practical way to choose
Start with the groove width. If it is 3/4 inch, the Whiteside 1031 is the direct match. If it is 11/16 inch, the Whiteside 1029 fits without a second pass. If you need a wider groove or general-purpose routing with a 1/2-inch collet, the Whiteside 1099 is the appropriate size. Then check the LOC against your deepest cut and confirm the shank and RPM against your router. The catalog gives you the diameter, LOC, shank and RPM for each bit; use those numbers as the decision framework rather than guessing from the model name.




