The kerf is the first decision, not the last
Slot cutter router bits are sized by kerf—the width of the slot they cut. Before you compare brands or prices, measure the panel or insert that must sit in the groove. A bit that is too narrow leaves a slot you have to widen in a second pass; one that is too wide creates a loose fit that no amount of clamping will fix.
The two Whiteside slot cutters in this catalog illustrate the range clearly: the 6700A cuts a 1/16′′ kerf, while the 6712A cuts a 9/32′′ kerf. Both are carbide-tipped three-wing cutters with a 5/16′′ bore and a 1-7/8′′ large diameter, and both require an arbor sold separately. The difference in kerf is what sends each bit to a different job.
Whiteside 6700A: the narrow 1/16′′ kerf
- .062″ 1/16″ Slot Cutter – Whiteside 6700A: Fractional kerf: 1/16′′; decimal kerf: .062′′ This is the narrowest slot in the pair, suited to thin panels, backer boards, or fine reveal grooves where a wider cutter would remove too much material.

.062″ 1/16″ Slot Cutter – Whiteside 6700A - .062″ 1/16″ Slot Cutter – Whiteside 6700A: Bore: 5/16′′; large diameter: 1-7/8′′; recommended RPM: 13,000 The bore tells you which arbor to pair with the cutter, and the recommended RPM gives you a starting point for setting up your router or CNC spindle.
Whiteside 6712A: the wider 9/32′′ kerf
- .281″ 9/32″ Slot Cutter – Whiteside 6712A: Fractional kerf: 9/32′′; decimal kerf: .281′′ At more than four times the width of the 1/16′′ cutter, this bit removes a much wider channel in one pass—useful when the panel or insert is closer to 1/4′′ thick.

.281″ 9/32″ Slot Cutter – Whiteside 6712A - .281″ 9/32″ Slot Cutter – Whiteside 6712A: Bore: 5/16′′; large diameter: 1-7/8′′; recommended RPM: 13,000 The shared bore and diameter mean the same arbor family and similar setup geometry apply, so the kerf width is the main variable between the two bits.
How to translate panel thickness into kerf
Start with the actual thickness of the panel, insert, or spline that will sit in the slot. If the material measures close to 1/16′′, the 6700A is the direct match. If it measures closer to 9/32′′, the 6712A is the direct match. For anything in between, you are choosing between a slot that needs a second pass to widen or a slot that leaves a small gap—and that trade-off depends on whether the joint will be glued, captured, or left dry.
Do not assume the nominal panel thickness printed on the label matches the caliper reading. Measure the piece you will actually install. The kerf numbers on these bits are precise—.062′′ and .281′′—so a few thousandths of an inch in the panel can change which bit fits best.
The arbor and bearing details that change the cut
- Both cutters require an arbor sold separately: Neither the 6700A nor the 6712A includes the arbor needed to mount it. Confirm your arbor matches the 5/16′′ bore before ordering, and check that your router or CNC collet accepts the arbor shank.
- Bearings set the depth of cut: The catalog notes that adding a different size bearing changes the depth of cut. For both cutters, the B20 bearing gives a 9/16′′ depth of cut, the B25 gives 3/8′′, the B26 gives 1/4′′, and the B27 gives 5/8′′. The bearing choice is separate from the kerf choice.
- Kerf and depth are independent decisions: The 1/16′′ and 9/32′′ cutters share the same bearing options, so you can pair either kerf with any of those depths. Decide the slot width first, then select the bearing that produces the groove depth your project needs.
1/16′′ vs 9/32′′ slot cutter at a glance
- Whiteside 6700A: 1/16′′ (0.062′′) kerf; 5/16′′ bore; 1-7/8′′ large diameter; 13,000 RPM recommended; carbide-tipped three-wing; arbor sold separately.
- Whiteside 6712A: 9/32′′ (0.281′′) kerf; 5/16′′ bore; 1-7/8′′ large diameter; 13,000 RPM recommended; carbide-tipped three-wing; arbor sold separately.
When the 1/16′′ cutter is the better fit
Choose the 6700A when the slot is a fine detail: a thin back panel, a narrow reveal, or a groove for material that measures near 1/16′′. The narrow kerf removes less material per pass, which can matter on thin stock or when you want the slot to disappear into a joint. Because it is the same body diameter and bore as the wider cutter, it does not demand a different arbor or a different router setup—only a different expectation of slot width.
When the 9/32′′ cutter earns its place
Choose the 6712A when the panel or insert is closer to 1/4′′ or when you need a wider channel in a single pass. The 9/32′′ kerf is a better match for thicker splines and panel goods, and it reduces the need to widen a narrow slot with a second cut. The trade-off is that a wider kerf removes more material, so the fit depends on measuring the panel accurately rather than assuming a nominal size.
What the catalog does not settle
The supplied records do not include a specific arbor model number, a shank size for the arbor, or step-by-step mounting instructions. They also do not state which bearing ships with either cutter. Use the kerf and bore facts here to narrow the choice, then confirm arbor compatibility and bearing selection against the product listing or the manufacturer before you cut. If your panel thickness falls between the two kerfs, test on scrap first—the right bit is the one that fits the material you actually have.



