العودة إلى المدونة
أدلة إرشادية 2026-11-20 Premium CNC & Router Bits for Precision Cutting 1 مشاهدة

Using a Metal Engraving Tool Kit on Brass & Aluminum

Using a Metal Engraving Tool Kit on Brass & Aluminum

Learn how to use an 80-degree engraving tool kit on brass and aluminum, including shank size selection and tip size guidance.

Choosing the Right Engraving Tool Kit for Brass and Aluminum

For clean, precise engraving on metals like brass and aluminum, an 80-degree V-bit tool kit offers the versatility you need. These solid carbide cutters produce a V-shaped pass, ideal for fine lettering, decorative lines, and marking. The key is matching the tool to your material and machine setup.

Both the 1/4 shank and 1/8 shank versions of the Tool Kit for Engraving Metals 80 Degree are designed to handle a wide range of materials, including steel, stainless steel, aluminum, wood, resin, plastics, acrylics, and soft metals such as brass and copper. For brass and aluminum, the 80-degree angle provides a balanced cut depth and width, reducing chatter and producing clean edges.

Tool Kit for Engraving Metals 80 Degree Options

  • Tool Kit for Engraving Metals 80 Degree – 1/4 shank: Shank Size: 1/4 (.250); Tool Length: 2 inches; 5 pack of solid carbide engraving cutters with 80 degree angle. The 1/4 shank fits most standard CNC routers and provides greater rigidity for deeper or faster engraving passes on metals like brass and aluminum.
    Tool Kit for Engraving Metals 80 Degree – 1/4 shank
    Tool Kit for Engraving Metals 80 Degree – 1/4 shank
  • Tool Kit for Engraving Metals 80 Degree – 1/8 shank: Shank Size: 1/8 (.125); Tool Length: 1-1/2 inches; 5 pack of solid carbide engraving cutters with 80 degree angle. The 1/8 shank is ideal for smaller spindles or collets, offering a lighter tool for delicate engraving work on thinner or softer metal pieces.
    Tool Kit for Engraving Metals 80 Degree – 1/8 shank
    Tool Kit for Engraving Metals 80 Degree – 1/8 shank

Selecting the Cutting Tip Size for Your Metal Engraving

Each 5-pack of the 80-degree engraving tool kit includes five different cutting tip sizes: .005, .010, .015, .020, and .030. The cutting tip determines how wide the engraved line will be. For brass and aluminum, a smaller tip like .005 or .010 is excellent for fine details, small text, and intricate patterns. The .030 tip produces a wider cut, suitable for bolder lettering or deeper marking.

Start with a smaller tip on a scrap piece of your material to test the cut depth and width. Because brass and aluminum are relatively soft compared to steel, you can achieve clean results with moderate feed rates. The 80-degree angle helps the tip penetrate without excessive force, reducing the risk of tool breakage.

Setting Up Your CNC for Brass and Aluminum Engraving

  1. Secure the material: Clamp your brass or aluminum workpiece firmly to the CNC bed to prevent movement during engraving. Use a vacuum table or double-sided tape for thin sheets.
  2. Choose the shank size: Select the 1/4 shank kit for standard routers or the 1/8 shank kit for smaller spindles. Ensure your collet matches the shank diameter exactly.
  3. Insert the tool: Place the desired tip size into the collet, leaving minimal exposed length beyond the collet to reduce vibration. Tighten securely.
  4. Set the depth: For brass and aluminum, a shallow pass is often sufficient for clear engraving. Adjust based on your material hardness and desired visibility, following the supplied product instructions.
  5. Run a test pass: Engrave a test line on scrap to verify depth and width. Increase depth gradually if a deeper mark is needed, but avoid exceeding the tip's capacity.

Material Considerations for Brass and Aluminum

Brass and aluminum are softer than steel, so they engrave more easily, but they can also cause gumming or chip welding if feed rates are too slow. Use a moderate feed rate and consider a light mist of cutting fluid or air blast to clear chips. The solid carbide construction of these bits resists wear, but sharpness is critical for clean cuts in non-ferrous metals.

Both tool kits are made in the USA by Bits & Bits and come as a 5-pack, saving 20% off the list price. This gives you a full range of tip sizes to experiment with, making it easier to find the perfect setting for your specific brass or aluminum project.

مقالات ذات صلة

Customer Service
الرئيسية
المنتجات
السلة
الملف الشخصي